News:

Thank you for your patience during the Forum downtime while we upgraded the software. Welcome back and see this thread for some new features and other changes to the forum.

Main Menu

F.M 170

Started by BigMattFromTexas, September 23, 2009, 10:04:02 PM

Previous topic - Next topic

BigMattFromTexas

Ive never been on this road, but ive seen Pictures.


xonhulu

I had the pleasure of driving FM 170 three years ago, and it was great.  Easily one of the coolest roads I've ever driven.

J N Winkler

This is my favorite FM 170 picture (taken late December 2001):

http://winklers-roads.fotopic.net/p9008103.html

Many (not all) of the pictures in this gallery are from FM 170.

http://winklers-roads.fotopic.net/c337179.html

I really would like to go back to Big Bend National Park.
"It is necessary to spend a hundred lire now to save a thousand lire later."--Piero Puricelli, explaining the need for a first-class road system to Benito Mussolini

agentsteel53

I've always wondered where they came up with 58420 pounds as a seemingly standard weight limit.  It's not an even multiple of metric tons (2200 pounds). 
live from sunny San Diego.

http://shields.aaroads.com

jake@aaroads.com

J N Winkler

I don't know the answer to that one.  The sign is R12-1T in the regulatory signs chapter of Standard Highway Sign Designs for Texas and the design for it does say "58420," but in keyline, implying that the precise limit can be varied to match the actual load capacity of the structure.  My best guess is that 58420 pounds is based on a particular type of slab-and-post construction which was standardized and used (probably to excess) on FM and RM roads in pre-Interstate (possibly pre-World War II) days.
"It is necessary to spend a hundred lire now to save a thousand lire later."--Piero Puricelli, explaining the need for a first-class road system to Benito Mussolini

agentsteel53

I remember seeing a similar number in Mississippi.  Might be the same number, but I could've sworn the Miss. standard had a 7 in it.  It was around 60,000 as well.
live from sunny San Diego.

http://shields.aaroads.com

jake@aaroads.com

BigMattFromTexas

Quote from: J N Winkler on September 24, 2009, 01:22:03 PM
This is my favorite FM 170 picture (taken late December 2001):

http://winklers-roads.fotopic.net/p9008103.html

Many (not all) of the pictures in this gallery are from FM 170.

http://winklers-roads.fotopic.net/c337179.html

I really would like to go back to Big Bend National Park.

Id like to go back to Big Bend also!
BigMatt

Sykotyk

Quote from: J N Winkler on September 24, 2009, 05:10:37 PM
I don't know the answer to that one.  The sign is R12-1T in the regulatory signs chapter of Standard Highway Sign Designs for Texas and the design for it does say "58420," but in keyline, implying that the precise limit can be varied to match the actual load capacity of the structure.  My best guess is that 58420 pounds is based on a particular type of slab-and-post construction which was standardized and used (probably to excess) on FM and RM roads in pre-Interstate (possibly pre-World War II) days.

I was looking it up as well. Apparantly when most of these roads were first being paved, 58,420 was a standard GVW (Gross Vehicle Weight), so it was made a standard weight rating for the roads (just like most roads now have an 80,000 GVW). Of course, roads or bridges can handle much more, but consistently taking that beating will wear the road/bridge out faster. However, most loads can get a permit to carry much heavier loads on the roads if needed. The absolute 'failure weight' of a road or bridge is probably much higher than even they'll admit.

The problem with most FM roads I've encountered in Texas is that they don't seem to A) have a solid base under the blacktop and B) not really wide enough for an 8'6 wide vehicle to pass each other.

Either way, most know that 58420 is a Texas standard. Besides, unless someone is actually weighing every truck that goes down the road, there's nothing to stop overweight trucks from taking the road.

Sykotyk

agentsteel53

#8
Quote from: Sykotyk on October 01, 2009, 04:15:34 PM
The absolute 'failure weight' of a road or bridge is probably much higher than even they'll admit.

probably around this much:

http://graphics1.snopes.com/photos/accident/graphics/housebridge2.jpg
live from sunny San Diego.

http://shields.aaroads.com

jake@aaroads.com

Sykotyk

Can't hotlink snopes, apparently. But I know the story you're talking about. They were moving the house in Canada and the DOT-esque agency accidentally routed them down the wrong back road to its final destination?

That's a matter of weight per axle. Hardly any bridge would stand up to that. Even on major bridges the decking can't support it. That's why the super loads (i.e., those behemoths weighing in at 80-160 TONS have an ungodly number of axles, huge pilot/escort teams to block roads to make sure that vehicle is the only thing on the bridge at a time, and exact times they're allowed to move, for how long, what speed, etc) must get their axle weights to a somewhat reasonable weight so as to not warp/crush/shatter the bridge as it crosses over. Plus, most truck tires can't stand too much weight. Most probably can only handle about 5-6,000 pounds each. Love seeing those trucks with 20+ axle trailers, 8 wheels per axle, helper truck in the back, creaping up a hill at 2mph with squad of escorts, police, and road service out assisting.

Sykotyk
Sykotyk



Opinions expressed here on belong solely to the poster and do not represent or reflect the opinions or beliefs of AARoads, its creators and/or associates.